Fax quote form from Insulgard Corporation for bullet-resisting door systems at the World Trade Center dated May 1998.
NYC-WTC_000172426–000172428Folder label: “None”
OCR status: ok · source: pdftotext
NYC 9/11 Public Portal Document
Technical Dat 9133 Lawrence Place, Hyattsville, MD 20761 600-638^718 301-927-8855 Fax 301-927-4531
HM544 DOOR SYSTEM - CLAMP-ON FRAME DOOR INSTALLATION
1. Remove door unit from crate and place on two saw horses, door stop side up. Sawhorses should approximately 3O'j~ong for a standard 36" door opening. Open frame to approximate 105 degree Remove the screws attaching the hinge to the frame. You do not have to remove screws from th door.
2. Check opening making sure it is approximately inch wider and inch taller than the zee anchors welded to the frame. Adjust the opening if necessary,
3. Remove door side of the frame by removing 10 flat head machine screws. Pull unit apart ending with 2 half frame sections.
4. Place the push side section of the jamb into the opening and shim between the anchor and stud Secure the frame to the wall studs or wall condition. Be sure not to pull the jamb into a rack or pi the sides out, because you must receive the door side of the jamb to complete the frame installation.
5. Plumb the hinge jamb both in and out, back and forth. The jam must be plumb for the door to sv properly.
6. Set the door side of the frame in the opening. Secure the two sections together with the flat hea screws you removed.
7. Hang the door and hinge to the frame.
8. Install the closer to the factory drilled location. Refer to the closer instructions for adjustment ner
9. If you are experiencing difficulty with the door closing equally around the frame, drill new attachments of the flat head machine screws and rack the frame to suit your condition. This als applies to a wall thicker than the frame was ordered for.
10. If a threshold is present, it needs to be custom fitted. Cut to the length and notch for your desire installation. Before installing the threshold, remove the temporary spreader welded to the frame Drill two 1/4" holes in the threshold to accept the anchors.
11. If electric hardware is present attach the power source to the terminal block as per wiring diagra located on the transom access panel. The access panel is a formed piece of channel attached t the header door stop. The diagram only identifies which wires are attached to which terminal, P.: to the manufacturers schematics for proper wiring connections or paths.
6/fd TES-OH daoo adysirisNi ssst-t ■ NYC-WTC_000172427
OCR can misread numbers and units. Confirm readings against the page image before using them.
Ranked by indexed similarity. Reasons describe shared subjects and filing context; check the source records.
NYC-WTC_000172431
Product feature description for Insulgard ICDS bullet-resisting door systems including heavy-duty aluminum construction dated May 1998.
1 shared topics · Same agency, volume and box · similarity 0.944
machine-extracted · confidence unavailable · Check page ↗NYC-WTC_000167926
Fax document detailing ballistic aluminum door specifications and construction requirements for a facility.
1 shared non-person entities · 1 shared topics · Same agency, volume and box · similarity 0.920
machine-extracted · confidence unavailable · Check page ↗NYC-WTC_000166810
Specification sheet detailing dimensions, pressure ratings, and UL classifications for pre-hung double leaf doors.
1 shared topics · Same agency, volume and box · similarity 0.903
machine-extracted · confidence unavailable · Check page ↗NYC-WTC_000172296
Fax cover sheet from Steelcraft transmitting documents regarding folding gates and grilles for the World Trade Center project.
1 shared topics · Same agency, volume and box · similarity 0.887
machine-extracted · confidence unavailable · Check page ↗NYC-WTC_000173050
Fax cover sheet from Steelcraft transmitting documents regarding folding gates and fire doors.
1 shared topics · Same agency, volume and box · similarity 0.885
machine-extracted · confidence unavailable · Check page ↗NYC-WTC_000173374
Architectural specification sheet detailing door models, dimensions, fire ratings, and security features for the OEM facility.
1 shared topics · Same agency, volume and box · similarity 0.874
machine-extracted · confidence unavailable · Check page ↗NYC-WTC_000168106
Portfolio document detailing selected boardroom and conference room projects completed by KBI Systems over three years.
1 shared topics · Same agency, volume and box · similarity 0.866
machine-extracted · confidence unavailable · Check page ↗NYC-WTC_000172420
Quotation form from Insulgard Corporation for products or services requested by a New York City agency.
Same agency, volume and box · similarity 0.862
machine-extracted · confidence unavailable · Check page ↗NYC-WTC_000172411
Fax proposal from National Bullet Proof Inc. describing bullet-resistant doors with EMI shielding dated May 19, 1998.
Same agency, volume and box · similarity 0.854
machine-extracted · confidence unavailable · Check page ↗NYC-WTC_000166793
Engineering calculation sheet for beam column design addressing lateral torsional buckling at World Trade Center.
1 shared topics · Same agency, volume and box · similarity 0.850
machine-extracted · confidence unavailable · Check page ↗NYC-WTC_000167919
Drawing detail specifying dimensions and specifications for a bullet-resistant package receiver.
1 shared topics · Same agency, volume and box · similarity 0.849
machine-extracted · confidence unavailable · Check page ↗NYC-WTC_000166488
Department of Buildings report containing findings and recommendations regarding the World Trade Center site.
1 shared topics · similarity 0.848
machine-extracted · confidence unavailable · Check page ↗Similar subjects in other documents. Similarity does not establish the same event, measurement or conclusion.
Page similarity is temporarily unavailable or this page has no indexed vector.
Readers open these alongside this record — through an Ask answer, the same folder, or indexed similarity. Not a claim they are about the same event.
NYC-WTC_000166926
Detailed technical specification document for generator procurement intended for the Mayor's Office of Emergency Management.
Filed in the same folder
NYC-WTC_000167197
One-page fax transmission log confirming authorization for scope revisions to the Mayor's Office of Emergency Management project.
Filed in the same folder
Internal memorandum from DCAS regarding space design for the Mayor's Office of Emergency Management at 7 World Trade Center.
Filed in the same folder
NYC-WTC_000167333
Invoice from architectural firm for Mayor's Office of Emergency Management reimbursable expenses related to World Trade Center project, including consulting and transportation…
Filed in the same folder
NYC-WTC_000167334
Invoice for consulting engineering services for Office of Emergency Management plans and specifications preparation at 7 World Trade Center.
Filed in the same folder